search
search
cancel
language
中国
韩国
韩国
韩国
韩国
韩国
News Center
/
/
/
Fuser film sleeve manufacturers will take you to understand: the causes and solutions of poor printer fixing

NEWS

CONTACT US

Balson Technology Co.,Ltd

  • Add:Room 8318, Wangcheng Building, Longguan East Road, Longhua New District, Shenzhen
  • Whatsapp Wechat: +86 13360528856

  • Skype:balson8_chips

  • Email:balson8@toner-chip.com

  • Url:www.toner-chip.com

     

     

Fuser film sleeve manufacturers will take you to understand: the causes and solutions of poor printer fixing

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-09-18 18:18
  • Views:

Fuser film sleeve manufacturers will take you to understand: the causes and solutions of poor printer fixing

(Summary description)The manufacturer of Fuser film sleeve tells you that you often encounter the phenomenon of powder falling during printing. The technical term is called poor fixing. The specific manifestation is that the toner cannot be fully melted or pressed into the paper. 

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2021-09-18 18:18
  • Views:
Information

The manufacturer of Fuser film sleeve tells you that you often encounter the phenomenon of powder falling during printing. The technical term is called poor fixing. The specific manifestation is that the toner cannot be fully melted or pressed into the paper. 

good price and quality Fuser film sleeve
The main reasons are as follows.
1. Poor fixing temperature
a. The fixing temperature of the printer is determined according to the thickness of the paper (such as plain paper, thick paper, etc.). The Fuser film sleeve manufacturer tells you if you are printing on thick paper, and the setting on the printer is plain paper, especially In this type of printing paper covered with toner on the entire surface, it is very easy to have insufficient fixing temperature, resulting in poor fixing. The solution is to set the appropriate printing paper.
b. The heat of the fuser is usually heated by the lamp tube inside the fuser roller. If the speed of the printer is relatively slow and the demand for heat is not high, then there is usually only one lamp tube. However, if it is a high-speed printer, because it needs to output a large amount of heat in a short time, it is necessary to design two lamps, one is mainly responsible for heating the middle area of ​​the paper, and the other is responsible for heating the two sides of the paper. The manufacturer of Fuser film sleeve tells you that if there is a problem with the lamps that are responsible for heating both sides of the paper, then there will be poor fixing on both sides of the paper. The solution is to replace the lamp.
2. Poor pressurization
The fuser is usually composed of a fuser roller and a pressure roller. The two are pressed by a spring to form a pressure area (Nip), which heats and presses the paper to achieve the purpose of fixing. There are one spring on each side of the fuser. If there is a problem with the spring on one side, the pressure on this side will not be enough, which will result in poor fixing. In this case, poor fixing usually starts from a certain part of the paper, and then spreads to the edge of the paper, and the degree of poor fixing will continue to increase. Solution Replace the spring.
3. Broken fixing roller
Today, when the laser printer technology is very mature, the fuser is a very interesting existence. The Fuser film sleeve manufacturer tells you that the fuser structure of each printer manufacturer is still very different. But one thing is that the heat must be applied to the paper through the fixing film. Some manufacturers’ fixing film is directly on the fixing roller (with a lamp inside), and some manufacturers heat the lamp independently, which passes through after heating the fixing film. Two pressure rollers perform fixing. To explain the structure of each fuser, first dig a hole, and I will fill it up and share it with you in the future.
The manufacturer of Fuser film sleeve tells you that if the fixing film is damaged, the heat cannot be evenly transferred to the paper, and the pressure will not be uniform when pressurized, which will lead to the bad fixing as shown in the figure above. Solution Replace the fuser roller (fixing film) or directly replace the fuser.

Keyword:

  • ABOUT US
BalsonTechnolog Co.,Ltd

Is a professional manufacturer and supplier of compatible toner cartridge

Copyright © 2020 Balson .粤ICP备11070211号

  • NAVIGATION
  • CONTACT US

Tel:+86-0755-23062280-812                   
Fax:+86-0755-29494906                    
Whatsapp:+86-
13360528856
Email: julia@toner-chip.com 
Address:3F, 2Building,TangZheng industrial park,GuanLan
road 152,longhua New Dis,shenzhen 518110,China

Skype
service hotline
0755 83808240 0755 83808240
Service time:
8:00 - 18:00
Skype:
Customer message